Premessa
Una fase importante nello sviluppo di un progetto di norma (UNI, ISO o CEN) sono le inchieste per la raccolta dei commenti e delle espressioni di voto.
La durata dell’inchiesta è legata al tipo di inchiesta in corso:
NWIP (CEN e ISO) – 3 mesi (se non diversamente deciso dal Technical Committee competente);
ISO/CD – 3 mesi (se non diversamente deciso dal Technical Committee competente);
ISO/DIS – 3 mesi;
prEN – 3 mesi;
ISO/FDIS – 2 mesi;
FprEN – 2 mesi.
Chiunque ritenga di avere commenti ad un progetto di norme può inoltrarli ad UNSIDER, gli associati che regolarmente partecipano alle attività degli Organi Tecnici dell’Ente attraverso ISOlution, tutti gli altri inviandoli alla Segreteria dell’Ente segreteria@unsider.it. I commenti dovranno essere inviati sull’apposito modulo e redatti in lingua inglese. Tutti i commenti verranno esaminati dal competente Organo Tecnico Unsider, deputato alla definizione nella posizione nazionale sul progetto.
Progetti UNSIDER in inchiesta prEN e ISO/DIS – maggio 2015 prEN – progetti di norma europei
prEN ISO 16530-1
Petroleum and natural gas industries. Well integrity. Part 1: Life cycle governance (ISO/DIS 16530-1:2015)
prEN 16808
Petroleum, petrochemical and natural gas industries. Safety of machineries. Manual elevators
EN 13480-8:2012/prA2
Metallic industrial piping. Part 8: Additional requirements for aluminium and aluminium alloy piping
ISO/DIS – progetti di norma internazionali
ISO/DIS 18203.2
Steel. Determination of the thickness of surface-hardened layers
ISO/DIS 16530-1
Petroleum and natural gas industries. Well integrity. Part 1: Life cycle governance
ISO/DIS 4545-2
Metallic materials. Knoop hardness test. Part 2: Verification and calibration of testing machines
ISO/DIS 4545-1
Metallic materials. Knoop hardness test. Part 1: Test method
ISO/DIS 14577-4
Metallic materials. Instrumented indentation test for hardness and materials parameters. Part 4: Test method for metallic and non-metallic coatings
ISO/DIS 4545-3
Metallic materials. Knoop hardness test. Part 3: Calibration of reference blocks
ISO/DIS 4545-4
Metallic materials. Knoop hardness test. Part 4: Table of hardness values
Progetti UNSIDER al voto FprEN e ISO/FDIS – maggio 2015 FprEN – progetti di norma europei
FprEN ISO 19901-1
Petroleum and natural gas industries. Specific requirements for offshore structures. Part 1: Metocean design and operating considerations (ISO/FDIS 19901-1:2015)
FprEN ISO 19901-8
Petroleum and natural gas industries. Specific requirements for offshore structures. Part 8: Marine soil investigations (ISO 19901-8:2014)
FprEN ISO 15156-1
Petroleum and natural gas industries. Materials for use in H2S-containing environments in oil and gas production. Part 1: General principles for selection of cracking-resistant materials (ISO/FDIS 15156-1:2015)
FprEN ISO 15156-2
Petroleum and natural gas industries. Materials for use in H2S-containing environments in oil and gas production. Part 2: Cracking-resistant carbon and low alloy steels, and the use of cast irons (ISO/FDIS 15156-2:2015)
FprEN ISO 15156-3
Petroleum and natural gas industries. Materials for use in H2S-containing environments in oil and gas production. Part 3: Cracking-resistant CRAs (corrosion-resistant alloys) and other alloys (ISO/FDIS 15156-3:2015)
EN 253:2009+A1:2013/FprA2
District heating pipes. Preinsulated bonded pipe systems for directly buried hot water networks. Pipe assembly of steel service pipe, polyurethane thermal insulation and outer casing of polyethylene
FprEN 15698-2
District heating pipes. Preinsulated bonded twin pipe systems for directly buried hot water networks. Part 2: Fitting and valve assembly of steel service pipes, polyurethane thermal insulation and outer casing of polyethylene
FprEN 1754
Magnesium and magnesium alloys. Designation system for anodes, ingots and castings. Material symbols and material numbers
ISO/FDIS – progetti di norma internazionali
ISO/FDIS 24817
Petroleum, petrochemical and natural gas industries. Composite repairs for pipework. Qualification and design, installation, testing and inspection
ISO/PRF 4969
Steel. Etching method for macroscopic examination
ISO/FDIS 15633
Iron ores. Determination of nickel. Flame atomic absorption spectrometric method
ISO/FDIS 10204
Iron ores. Determination of magnesium. Flame atomic absorption spectrometric method
ISO/FDIS 4689-3
Iron ores. Determination of sulfur content. Part 3: Combustion/infrared method
ISO/FDIS 10203
Iron ores. Determination of calcium. Flame atomic absorption spectrometric method
ISO/FDIS 15634
Iron ores. Determination of chromium content. Flame atomic absorption spectrometric method
ISO/FDIS 4689-2
Iron ores. Determination of sulfur content. Part 2: Combustion/titration method
ISO/FDIS 11536
Iron ores. Determination of loss on ignition. Gravimetric method
ISO/FDIS 19272
Low alloyed steel. Determination of C, Si, Mn, P, S, Cr, Ni, Ai, Ti and Cu. Glow discharge optical emission spectrometry (routine method)
ISO/FDIS 16468
Investment castings (steel, nickel alloys and cobalt alloys). General technical requirements
ISO/FDIS 4993
Steel and iron castings. Radiographic inspection
ISO/FDIS 11973
Heat-resistant cast steels and alloys for general applications
ISO/FDIS 14737
Cast non-alloy and low alloy steels for general applications
ISO/FDIS 13520
Determination of ferrite content in austenitic stainless steel castings
ISO/FDIS 14556
Metallic materials. Charpy V-notch pendulum impact test. Instrumented test method
ISO/FDIS 9477
High strength cast steels for general engineering and structural purposes
ISO/FDIS 13583-1
Centrifugally cast steel and alloy products. Part 1: General testing and tolerances
ISO/FDIS 4990
Steel castings. General technical delivery requirements
ISO/FDIS 19960
Cast steels and alloys with special physical properties
ISO/FDIS 13583-2
Centrifugally cast steel and alloy products. Part 2: Heat resistant materials
ISO/FDIS 11972
Corrosion-resistant cast steels for general applications
ISO/FDIS 11970
Specification and approval of welding procedures for production welding of steel castings
ISO/FDIS 643
Steel. Micrographic determination of the apparent grain size
ISO/FDIS 13521
Austenitic manganese steel castings
ISO/FDIS 4991
Steel castings for pressure purposes
ISO/FDIS 16859-1
Metallic materials. Leeb hardness test. Part 1: Test method
ISO/FDIS 16859-3
Metallic materials. Leeb hardness test. Part 3: Calibration of reference test blocks
ISO/FDIS 16859-2
Metallic materials. Leeb hardness test. Part 2: Verification and calibration of the testing instruments
ISO/FDIS 19901-1
Petroleum and natural gas industries. Specific requirements for offshore structures. Part 1: Metocean design and operating considerations
ISO/FDIS 16904
Petroleum and natural gas industries. Design and testing of LNG marine transfer arms for conventional onshore terminals
ISO/FDIS 15156-3
Petroleum and natural gas industries. Materials for use in H2S-containing environments in oil and gas production. Part 3: Cracking-resistant CRAs (corrosion-resistant alloys) and other alloys
ISO/FDIS 15156-2
Petroleum and natural gas industries. Materials for use in H2S-containing environments in oil and gas production. Part 2: Cracking-resistant carbon and low-alloy steels, and the use of cast irons
ISO/FDIS 15156-1
Petroleum and natural gas industries. Materials for use in H2S-containing environments in oil and gas production. Part 1: General principles for selection of cracking-resistant materials
ISO/FDIS 4689-2
Iron ores. Determination of sulfur content. Part 2: Combustion/titration method
ISO/FDIS 4689-3
Iron ores. Determination of sulfur content. Part 3: Combustion/infrared method
ISO/FDIS 10203
Iron ores. Determination of calcium. Flame atomic absorption spectrometric method
ISO/FDIS 10204
Iron ores. Determination of magnesium. Flame atomic absorption spectrometric method
ISO/FDIS 11536
Iron ores. Determination of loss on ignition. Gravimetric method
ISO/FDIS 15633
Iron ores. Determination of nickel. Flame atomic absorption spectrometric method
ISO/FDIS 15634
Iron ores. Determination of chromium content. Flame atomic absorption spectrometric method
ISO/FDIS 24817 Petroleum, petrochemical and natural gas industries. Composite repairs for pipework. Qualification and design, installation, testing and inspection
Fonte: siderweb.com
