Giovedì, 14 Maggio 2015 00:00

UNSIDER - Progetti allo studio

Premessa

Una fase importante nello sviluppo di un progetto di norma (UNI, ISO o CEN) sono le inchieste per la raccolta dei commenti e delle espressioni di voto.

La durata dell’inchiesta è legata al tipo di inchiesta in corso:

 

NWIP (CEN e ISO) – 3 mesi (se non diversamente deciso dal Technical Committee competente);

ISO/CD – 3 mesi (se non diversamente deciso dal Technical Committee competente);

ISO/DIS – 3 mesi;

prEN – 3 mesi;

ISO/FDIS – 2 mesi;

FprEN – 2 mesi.

 

Chiunque ritenga di avere commenti ad un progetto di norme può inoltrarli ad UNSIDER, gli associati che regolarmente partecipano alle attività degli Organi Tecnici dell’Ente attraverso ISOlution, tutti gli altri inviandoli alla Segreteria dell’Ente Questo indirizzo email è protetto dagli spambots. E' necessario abilitare JavaScript per vederlo.. I commenti dovranno essere inviati sull’apposito modulo e redatti in lingua inglese. Tutti i commenti verranno esaminati dal competente Organo Tecnico Unsider, deputato alla definizione nella posizione nazionale sul progetto.

 

 

Progetti UNSIDER in inchiesta prEN e ISO/DIS - maggio 2015 prEN – progetti di norma europei

 

prEN ISO 16530-1

Petroleum and natural gas industries. Well integrity. Part 1: Life cycle governance (ISO/DIS 16530-1:2015)

 

prEN 16808

Petroleum, petrochemical and natural gas industries. Safety of machineries. Manual elevators

 

EN 13480-8:2012/prA2

Metallic industrial piping. Part 8: Additional requirements for aluminium and aluminium alloy piping

 

 

ISO/DIS – progetti di norma internazionali

 

ISO/DIS 18203.2

Steel. Determination of the thickness of surface-hardened layers

 

ISO/DIS 16530-1

Petroleum and natural gas industries. Well integrity. Part 1: Life cycle governance

 

ISO/DIS 4545-2

Metallic materials. Knoop hardness test. Part 2: Verification and calibration of testing machines

 

ISO/DIS 4545-1

Metallic materials. Knoop hardness test. Part 1: Test method

 

ISO/DIS 14577-4

Metallic materials. Instrumented indentation test for hardness and materials parameters. Part 4: Test method for metallic and non-metallic coatings

 

ISO/DIS 4545-3

Metallic materials. Knoop hardness test. Part 3: Calibration of reference blocks

 

ISO/DIS 4545-4

Metallic materials. Knoop hardness test. Part 4: Table of hardness values

 

 

Progetti UNSIDER al voto FprEN e ISO/FDIS - maggio 2015 FprEN – progetti di norma europei

 

FprEN ISO 19901-1

Petroleum and natural gas industries. Specific requirements for offshore structures. Part 1: Metocean design and operating considerations (ISO/FDIS 19901-1:2015)

 

FprEN ISO 19901-8

Petroleum and natural gas industries. Specific requirements for offshore structures. Part 8: Marine soil investigations (ISO 19901-8:2014)

 

FprEN ISO 15156-1

Petroleum and natural gas industries. Materials for use in H2S-containing environments in oil and gas production. Part 1: General principles for selection of cracking-resistant materials (ISO/FDIS 15156-1:2015)

 

FprEN ISO 15156-2

Petroleum and natural gas industries. Materials for use in H2S-containing environments in oil and gas production. Part 2: Cracking-resistant carbon and low alloy steels, and the use of cast irons (ISO/FDIS 15156-2:2015)

 

FprEN ISO 15156-3

Petroleum and natural gas industries. Materials for use in H2S-containing environments in oil and gas production. Part 3: Cracking-resistant CRAs (corrosion-resistant alloys) and other alloys (ISO/FDIS 15156-3:2015)

 

EN 253:2009+A1:2013/FprA2

District heating pipes. Preinsulated bonded pipe systems for directly buried hot water networks. Pipe assembly of steel service pipe, polyurethane thermal insulation and outer casing of polyethylene

 

FprEN 15698-2

District heating pipes. Preinsulated bonded twin pipe systems for directly buried hot water networks. Part 2: Fitting and valve assembly of steel service pipes, polyurethane thermal insulation and outer casing of polyethylene

 

FprEN 1754

Magnesium and magnesium alloys. Designation system for anodes, ingots and castings. Material symbols and material numbers

 

 

ISO/FDIS – progetti di norma internazionali

 

ISO/FDIS 24817

Petroleum, petrochemical and natural gas industries. Composite repairs for pipework. Qualification and design, installation, testing and inspection

 

ISO/PRF 4969

Steel. Etching method for macroscopic examination

 

ISO/FDIS 15633

Iron ores. Determination of nickel. Flame atomic absorption spectrometric method

 

ISO/FDIS 10204

Iron ores. Determination of magnesium. Flame atomic absorption spectrometric method

 

ISO/FDIS 4689-3

Iron ores. Determination of sulfur content. Part 3: Combustion/infrared method

 

ISO/FDIS 10203

Iron ores. Determination of calcium. Flame atomic absorption spectrometric method

 

ISO/FDIS 15634

Iron ores. Determination of chromium content. Flame atomic absorption spectrometric method

 

ISO/FDIS 4689-2

Iron ores. Determination of sulfur content. Part 2: Combustion/titration method

 

ISO/FDIS 11536

Iron ores. Determination of loss on ignition. Gravimetric method

 

ISO/FDIS 19272

Low alloyed steel. Determination of C, Si, Mn, P, S, Cr, Ni, Ai, Ti and Cu. Glow discharge optical emission spectrometry (routine method)

 

ISO/FDIS 16468

Investment castings (steel, nickel alloys and cobalt alloys). General technical requirements

 

ISO/FDIS 4993

Steel and iron castings. Radiographic inspection

 

ISO/FDIS 11973

Heat-resistant cast steels and alloys for general applications

 

ISO/FDIS 14737

Cast non-alloy and low alloy steels for general applications

 

ISO/FDIS 13520

Determination of ferrite content in austenitic stainless steel castings

 

ISO/FDIS 14556

Metallic materials. Charpy V-notch pendulum impact test. Instrumented test method

 

ISO/FDIS 9477

High strength cast steels for general engineering and structural purposes

 

ISO/FDIS 13583-1

Centrifugally cast steel and alloy products. Part 1: General testing and tolerances

 

ISO/FDIS 4990

Steel castings. General technical delivery requirements

 

ISO/FDIS 19960

Cast steels and alloys with special physical properties

 

ISO/FDIS 13583-2

Centrifugally cast steel and alloy products. Part 2: Heat resistant materials

 

ISO/FDIS 11972

Corrosion-resistant cast steels for general applications

 

ISO/FDIS 11970

Specification and approval of welding procedures for production welding of steel castings

ISO/FDIS 643

Steel. Micrographic determination of the apparent grain size

 

ISO/FDIS 13521

Austenitic manganese steel castings

 

ISO/FDIS 4991

Steel castings for pressure purposes

 

ISO/FDIS 16859-1

Metallic materials. Leeb hardness test. Part 1: Test method

 

ISO/FDIS 16859-3

Metallic materials. Leeb hardness test. Part 3: Calibration of reference test blocks

 

ISO/FDIS 16859-2

Metallic materials. Leeb hardness test. Part 2: Verification and calibration of the testing instruments

 

ISO/FDIS 19901-1

Petroleum and natural gas industries. Specific requirements for offshore structures. Part 1: Metocean design and operating considerations

 

ISO/FDIS 16904

Petroleum and natural gas industries. Design and testing of LNG marine transfer arms for conventional onshore terminals

 

ISO/FDIS 15156-3

Petroleum and natural gas industries. Materials for use in H2S-containing environments in oil and gas production. Part 3: Cracking-resistant CRAs (corrosion-resistant alloys) and other alloys

 

ISO/FDIS 15156-2

Petroleum and natural gas industries. Materials for use in H2S-containing environments in oil and gas production. Part 2: Cracking-resistant carbon and low-alloy steels, and the use of cast irons

 

ISO/FDIS 15156-1

Petroleum and natural gas industries. Materials for use in H2S-containing environments in oil and gas production. Part 1: General principles for selection of cracking-resistant materials

 

ISO/FDIS 4689-2

Iron ores. Determination of sulfur content. Part 2: Combustion/titration method

 

ISO/FDIS 4689-3

Iron ores. Determination of sulfur content. Part 3: Combustion/infrared method

 

ISO/FDIS 10203

Iron ores. Determination of calcium. Flame atomic absorption spectrometric method

 

ISO/FDIS 10204

Iron ores. Determination of magnesium. Flame atomic absorption spectrometric method

 

ISO/FDIS 11536

Iron ores. Determination of loss on ignition. Gravimetric method

 

ISO/FDIS 15633

Iron ores. Determination of nickel. Flame atomic absorption spectrometric method

 

ISO/FDIS 15634

Iron ores. Determination of chromium content. Flame atomic absorption spectrometric method

 

ISO/FDIS 24817 Petroleum, petrochemical and natural gas industries. Composite repairs for pipework. Qualification and design, installation, testing and inspection

 



Fonte: siderweb.com

Ultima modifica il Giovedì, 14 Maggio 2015 09:01

icon80x80

 

appstore

googleplay

windows-badge

Calendario News

« Agosto 2017 »
Lun Mar Mer Gio Ven Sab Dom
  1 2 3 4 5 6
7 8 9 10 11 12 13
14 15 16 17 18 19 20
21 22 23 24 25 26 27
28 29 30 31      

Questo sito web utilizza i cookies per gestire l'autenticazione, la navigazione, e altre funzioni. Navigando sul nostro sito, accetti che possiamo utilizzare questi tipi di cookies. Per saperne di più sui cookies che utilizziamo vedi la nostra privacy policy.

Accetto i cookies da questo sito.